You get both the front and rear heavy duty Currie axle housings (listed below) as well as a Yukon premier Air locker (with 6 yr warranty) and a high quality gear set, all setup and ready for paint and your calipers on the front and your rotors and calipers on the rear.
FRONT:
The RockJock III high pinion frontend assembly for the 2007 and up Jeep JK includes the complete housing featuring the 65-45-12 ductile iron housing center (highest ground clearance 60 on the market), AR400 heat treated bottom skid plate allowing the axle to slide over rocks easily, 3" x .375" wall d.o.m. steel tubes, 1 ton inner knuckles, 5/16" thick heavy steel diff cover, yoke, and all new heavy duty Currie Jeep JK suspension brackets mounted. Upper control arm brackets are equipped with Johnny Joint rod ends for maximum articulation.
Axles shafts are the Currie performance 4340 35 spline inner and outer with Spicer 1480 u-joints. Outer assemblies include 1 ton outer knuckles featuring Currie "high steer" steering arm and ball joints installed, Currie exclusive 1 ton unit bearings with 5 on 5 1/2" wheel bolt pattern and JK tone rings allowing for ABS and ESP retention, 13" vented rotors (over 1" greater diameter than stock for increased braking), zinc plated caliper brackets that allow the use of the stock JK front calipers, Currie drive flanges or premium manual locking hubs, and our heavy duty 1 3/8" o.d. 4130 chrome moly tie rod with tie rod ends.
NOTES: This unit is 68.75" wide. This unit requires the use of 17" wheels. 2012 and newer vehicles will need a computer programmer, such as the AEV ProCal Module to reset the gear ratio and tire height in the vehicle's computer.
REAR:
The RockJock III high pinion rearend assembly for the 2007 and up Jeep JK includes the complete housing with the 65-45-12 ductile iron housing center, AR400 heat treated bottom skid plate allowing the axle to slide over rocks easily, 3" x .375" wall d.o.m. steel tubes, heavy duty steel diff cover, yoke (1310/1330/1350 optional), and custom housing ends that accept set 80 axle bearings (over 50% greater capacity than stock) and allow for all factory disc brake hardware and ABS and ESP sensors to bolt back on. All new heavy duty Currie Jeep JK suspension brackets are mounted and feature multiple control arm mounting holes, multiple trac bar mounting holes, and adjustable shock mounting holes.
Also included are the Currie performance forged alloy 35 spline axle shafts. Axles feature wheel studs, ABS tone rings, and axle bearings pressed on, as well as the bearing retainer plates.
Your JK's stock rotors, calipers, and caliper mounting brackets transfer over!
NOTES: This unit is 66" wide. YOU WILL NEED TO have your stock rotors drilled to a 5x5.5" pattern, or select new Currie rotors with your order.
Then for the lockers you get:
The Yukon Zip Locker, an Air Operated locker similar in design to the ARB Air Locker. Zip Lockers feature a forged case and use 4320 high-nickel Chrome-Moly steel for added strength. Zip Lockers work with a variety of air delivery systems including air compressors, on-board air, powertanks, and more. All Zip Lockers are assembled in the USA.
Air operated locking differential designed with severe off-road use in mind.
Its 8620 case & 4320 steel internals provide maximum strength against failure and give you piece of mind on the trail.
Each unit comes with a variety of small parts for installation and operation, including air line and fittings, seal housing, shims, (if applicable) operation switch with front and rear covers, zip ties and more.
Tested and assembled in the USA!
Backed by the Best Warranty in the Business.
-- $2,000 collateral damage warranty for the first two years (covers even LABOR).
-- Six year Best in the Business Warranty.
Gears ratio of your choice.
Yoke size of your choice.
5x5.5" wheel bolt pattern.
1/2" wheel studs.
Special shipping and handling required for this item, select shipping or local pickup. The added freight fee is in addition to the shipping fee added at check out.
These are a build to order direct from Currie and typically take between 10-20 business days to complete and ship.
85 visits